 |
| DISCONTINUED Foot switch |
|
Industrial engineered positive ON/OFF foot switch.
Easier operation
Added safety
|
$ 114
|
|
|
| DISCONTINUED 45 degree adjustable miter fixture |
|
The MK 45 degree adjustable miter fixture is designed to hold tiles up to 14".
Tough construction
|
$ 153
|
|
|
| Dressing stone |
|
MK Diamond's specially formulated 60-grit dressing stone is used to expose new cutting surfaces.
A must for the professional
|
$ 14
|
|
|
| Electric water pump |
|
120V water pump
Designed specifically and only for the MK 370 and MK 470
90 gallons per hour
|
$ 44
|
|
|
| Electric water pump |
|
120V water pump
Designed for use with all MK tile saws
150 gallons per hour
|
$ 59
|
|
|
| Electric water pump |
|
120V water pump
Designed for use with MK Diamond brick and block saws
Powerful 225 gallons per hour
|
$ 75.19
|
|
|
| Centrifugal water pump |
|
Centrifugal water pump
Designed specifically for the MK-5005 GH
|
$ 356
|
|
|
| Centrifugal water pump |
|
Centrifugal water pump
Designed specifically for the MK-5005S
|
$ 284
|
|
|
| Tile hole cutter |
|
These zinc-plated tile hole cutters can be adjusted to cut one to three inch holes.
Extra carbide tips can be ordered separately
|
$ 25
|
|
|
| 90 degree squaring arm |
|
Rip guide ensures accurate 90 degree cuts.
Heavy-duty cast aluminum
|
$ 29
|
|
|
| MK-290 1 3/8 inch tile bit |
|
The MK-290 Tile Bit is designed to cut clean, smooth 1 3/8 inch holes through all ceramic tile and marble. It can be used wet or dry.
Can be used wet or dry
Cuts 1 3/8" holes
|
$ 99
|
|
|
| MK-290 1 1/2 inch tile bit |
|
The MK-290 Tile Bit is designed to cut clean, smooth 1 1/2 inch holes through all ceramic tile and marble.
Can be used wet or dry
Cuts 1 1/2" holes
|
$ 122
|
|
|
| MK-290 2 1/2 inch tile bit |
|
The MK-290 Tile Bit is designed to cut clean, smooth 2 1/2 inch holes through all ceramic tile and marble.
Can be used wet or dry
Cuts 2 1/2" holes
|
$ 186
|
|
|
| Cutting Kit |
|
The Cutting Kit includes a 90° Protractor, Dressing Stone, Dual 45° Flat Angle Guide, and a large 45° Bullnose Miter.
Collection of MK cutting accessories
|
$ 108
|
|
|
| Adjustable rip guide |
|
Adjustable rip guide.
Cast aluminum
|
$ 20
|
|
|
| DISCONTINUED Rip guide |
|
Rip guide.
Cast aluminum
|
$ 30
|
|
|
| Dual 45 degree flat angle guide |
|
The dual 45 degree flat angle guide, designed to give you a perfect 45 degree flat edge.
Cast aluminum
|
$ 23
|
|
|
| 90 degree protractor |
|
The 90 degree protaractor, allows you to cut the perfect angles.
Cast aluminum
|
$ 32
|
|
|
| 45 degree large bullnose miters |
|
The large 45 degree Bullnose Miters is designed to give you perfect 45 degree miter edge.
Cast aluminum
|
$ 53
|
|
|
| Ground fault interrupter |
|
Ground fault interrupters provide protection from the dangers of electrical hazards.
Added safety
|
$ 60
|
|
|
| DISCONTINUED Foot switch |
|
Industrial engineered positive ON/OFF foot switch.
Easier operation
Added safety
|
$ 114
|
|
|
| 16 inch Tile cutter |
|
MK Scor-N-Set 16" Tile Cutter is small enough to hand carry but is still a precision-made professional tool.
Rugged diecast aluminum
Two 1/2" solid chrome plated steel slide rods.
|
$ 125
|
|
|
| 16 inch Tile cutter replacement wheel |
|
Replacement wheel for the 16" Scor-N-Set.
Perfect fit
Makes your scor-n-set like new again
|
$ 11
|
|
|
| Powercord adapter (male to female) |
|
Male/female powercord adapters.
|
$ 26
|
|
|
| Powercord adapter (female to male) |
|
Female/male powercord adapters.
|
$ 28
|
|
|
| Y-cord |
|
20 Amp / 125 V Y-cord adapter.
|
$ 46
|
|
|
| ATS saw stands |
|
Versatile and highly mobile saw stand with zinc-plated square steel tubing, 10" pneumatic tires, and removable side table.
Fits 101 Series, 880, 1070, 1080, and 2000 series saws.
|
$ 539
|
|
|
| Folding stand (standard table length) |
|
This sturdy steel stand allows the operator to have the work surface at a standing height.
Fits MK-101, 101 Pro, 660, 770, and 880.
Also fits the MK-1080 and 2000 series masonry saws.
Does not fit the 101 Pro24, 115 Pro or 1070 which have the larger size tables and require stand 153331
|
$ 140
|
|
|
| Folding stand (large table size) |
|
This sturdy stand allows the operator to have the work surface at a standing height.
Fits MK-101 Pro24, 115 Pro & 1070.
|
$ 140
|
|
|
| Water hood cover |
|
Two-piece water hood helps contain water and reduce water overspray around the work area.
Fits MK-770.
|
$ 200
|
|
|
| Water hood cover |
|
Two-piece water hood helps contain water around the work area.
Fits MK-370 and 470 saws.
|
$ 170
|
|
|
| 18 inch diagonal cutting kit |
|
MK 101 support fixture that permits diagonal cuts of 18".
Zinc plated
|
$ 150
|
|
|
| 24 inch tile cutting kit |
|
MK 101 support fixture that permits 24" straight rip cutting.
Zinc plated
|
$ 172
|
|
|
| Extra Drain plugs 2-pack |
|
Water Tray Plug - 2 pack.
MK Diamond markings
Perfect fit
|
$ 6
|
|
|
| Extra Drain plugs 6-pack |
|
Water Tray Plug - 6 pack.
MK Diamond markings
Perfect fit
|
$ 18
|
|
|
| Blade wear gauge |
|
A diamond blade "wear" measuring tool.
Measures 7" through 24" blades
Caters for 20mm, 3/4" or 5/8" arbor.
|
$ 219
|
|
|
| Water tank |
|
Top mounting water tank
Easy access for refilling
Fits the MK 1600 series saws
|
$ 149.92
|
|
